Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen gezeigt.
| — |
en:cs2_info [2016/04/12 12:56] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Using LDT-Decoder on the Central Station 2! ====== | ||
| + | |||
| + | |||
| + | {{ :de:cad:centralstation_02.gif?666x414 }} | ||
| + | |||
| + | |||
| + | The **Central Station 2** transmits commands of accessory decoders for switching turnouts and signals either via **Märklin-Motorola- or DCC-Format**. This data format enables the setting at the window “**Configuration Magnet Articles**” setting the individual address via the selection “**MM2**” or “**DCC**”. \\ \\ Therefore is the **Central Station 2** able to respond to the **LDT-Decoder** for the **Märklin-Motorola-Formats** (e.g. [[:en:qs-dec-2|QS-DEC-II]], [[:en:s-dec-4|S-DEC-4-MM]], [[:en:sa-dec-4|SA-DEC-4-MM]], [[:en:m-dec|M-DEC-MM]], [[:en:ls-dec-db|LS-DEC]], [[:en:tt-dec|TT-DEC]] and [[:en:tt-dec-r|TT-DEC-R]]) or to the DCC-Formats (e.g. [[en:s-dec-4|S-DEC-4-DC]], [[en:sa-dec-4|SA-DEC-4-DC]], [[en:m-dec|M-DEC-DC]], [[en:ls-dec-db|LS-DEC]], [[en:tt-dec|TT-DEC]] and [[en:tt-dec-r|TT-DEC-R]]). | ||
| + | \\ \\ | ||
| + | === Recommendations for the installation of LDT-Decoder on the Central Station 2: === | ||
| + | |||
| + | |||
| + | == 1. Connecting the Decoder to the Central Station 2 == | ||
| + | |||
| + | |||
| + | **LDT-Decoder** will get always the digital information via the “**Connection Layout**” (**standard track output**). This connection is located at the **Central Station 2** directly next to the power supply connection. At the **Central Station 2** identifies “**B**” the color “**red**” and “**0**” the color “**brown**”. | ||
| + | |||
| + | == 2. Programming the decoder address == | ||
| + | |||
| + | The **LDT-Decoder** has **not** to be connected to the programming-track output during the **programming** of the **decoder address**. The connection of the decoder to the **standard track output** shall remain. \\ | ||
| + | |||
| + | It is **important** for the **programming** that **no locomotive is active**. \\ | ||
| + | |||
| + | **Please proceed now as follows:** | ||
| + | |||
| + | 1. Tap at the section “**control**” on both loc-controller in succession onto the loc-image and select “**No Locomotive**”. \\ | ||
| + | |||
| + | 2. If both loc controller indicate “**No Locomotive**”, please select at the section “**setup**” the “**Restart**”.\\ | ||
| + | |||
| + | 3. After the restart of the Central Station 2 change into the “**keyboard**” and program your LDT Decoder as decribed within the relative instruction manual. | ||
| + | |||
| + | |||
| + | [[:en:cs2_info|{{ :de:images:zurueck_en_page.png?40x32}}]] Subject to technical changes and errors.\\ © 2016 by LDT | ||
